HP OfficeJet 6110 all-in-one

[Richard Werst]

I may be trying to saddle a dead horse here, but it would be nice to get
the scanner to work with this printer.

Using Debian Lenny, and trying to install an "HP OfficeJet 6110
all-in-one"

I have had success using Sane with a couple of stand-alone HP scanners
(3300C and 2200C), so the basic Sane utility is installed and should be
functioning properly.

HPLIP installs the software, and it will print properly.

scanimage -L returns "no SANE devices found"

 sane-find-scanner locates the unit: "found USB scanner (vendor=0x03f0
[Hewlett-Packard], product=0x2d11 [OfficeJet 6100 Series]) at
libusb:002:007"

Trying to scan with Xsane and gscan2pdf return "No devices available"
and the HPLIP scan utility gives an error message:  Failed to open
device 'hpaio:/usb/Officejet_6100_Series?serial=MY31UC23S12R': Invalid
argument.
will not work, with the HPLIP giving a error
I added "hpoj" to the dll.conf, and rebooted with the printer attached,
without any change in the messages.

Internet searches haven't brought any solutions, so I am hoping someone
on the list will have some suggestions.

Thanks in advance...

Richard



--
sane-devel mailing list: sane-devel@...
http://lists.alioth.debian.org/mailman/listinfo/sane-devel
Unsubscribe: Send mail with subject "unsubscribe your_password"
             to sane-devel-request@...

[Simon Matter]

> I may be trying to saddle a dead horse here, but it would be nice to get
> the scanner to work with this printer.
>
> Using Debian Lenny, and trying to install an "HP OfficeJet 6110
> all-in-one"
>
> I have had success using Sane with a couple of stand-alone HP scanners
> (3300C and 2200C), so the basic Sane utility is installed and should be
> functioning properly.
>
> HPLIP installs the software, and it will print properly.
>
> scanimage -L returns "no SANE devices found"
>
>  sane-find-scanner locates the unit: "found USB scanner (vendor=0x03f0
> [Hewlett-Packard], product=0x2d11 [OfficeJet 6100 Series]) at
> libusb:002:007"
>
> Trying to scan with Xsane and gscan2pdf return "No devices available"
> and the HPLIP scan utility gives an error message:  Failed to open
> device 'hpaio:/usb/Officejet_6100_Series?serial=MY31UC23S12R': Invalid
> argument.
> will not work, with the HPLIP giving a error
> I added "hpoj" to the dll.conf, and rebooted with the printer attached,
> without any change in the messages.

Do you have "hpaio" enabled in dll.conf and the hp* daemons from HPLIP are
running?

Simon

>
> Internet searches haven't brought any solutions, so I am hoping someone
> on the list will have some suggestions.
>
> Thanks in advance...
>
> Richard
>
>
>
> --
> sane-devel mailing list: sane-devel@...
> http://lists.alioth.debian.org/mailman/listinfo/sane-devel
> Unsubscribe: Send mail with subject "unsubscribe your_password"
>              to sane-devel-request@...
>

--
sane-devel mailing list: sane-devel@...
http://lists.alioth.debian.org/mailman/listinfo/sane-devel
Unsubscribe: Send mail with subject "unsubscribe your_password"
             to sane-devel-request@...

[Richard Werst]

Thanks for your reply Simon;

I added "hpaio" initially, which brought the same result, and then took
it out because I found a forum link that said it was not necessary/could
create a problem with the newer version of HPLIP (I'm running 2.8.6b).

In response to your email I put it in again with the same result.

HPLIP is running, and working properly I think, but I'm not sure what to
say about "hp* daemons."

Do they get activated at boot time, or are they called called when
needed?

RBW


--
sane-devel mailing list: sane-devel@...
http://lists.alioth.debian.org/mailman/listinfo/sane-devel
Unsubscribe: Send mail with subject "unsubscribe your_password"
             to sane-devel-request@...