RE: I2c and Avalon Bus

Can you hook up an oscilloscope and see any activity on SCL/SDA??

Richard



-----Original Message-----
From: cores-bounces@... [mailto:cores-bounces@...] On
Behalf Of K@nt
Sent: 29 May 2008 10:53
To: cores@...
Subject: [oc] I2c and Avalon Bus


Hello all,

I'm currently working on opencores I2C master (VHDL version) to
the NIOS 2 processor via the Avalon bus.(Stratix II)
There is an older post about this subject but I can't resolved my problem.

So I've used i2c_master_top_avalon.vhd and I've created a wrapper to use
this component with Avalon bus
http://www.nabble.com/file/p17530366/oc_i2c_master.vhd oc_i2c_master.vhd  

I've configured the component(
http://www.nabble.com/file/p17530366/component.jpg ) and attached this to a
NIOS 2 processor.( http://www.nabble.com/file/p17530366/sopc.jpg )

I've assigned Sda ans Scl  http://www.nabble.com/file/p17530366/pin.jpg 

So I use I2c to configure a video camera (
http://ltc.cit.cornell.edu/courses/ee476/FinalProjects/s2006/jzs3_da65/jzs3_
da65/C3088.pdf
http://ltc.cit.cornell.edu/courses/ee476/FinalProjects/s2006/jzs3_da65/jzs3_
da65/C3088.pdf
) but  i can't set this !!

I think the problem is it can't recognize the slave (video camera), in fact
when I write a value into the register of the video camera I'm waiting for
the TIP flag and RxACK flag but the RXACK always stay at '1'...

At start I've thought there was a problem with the slave adress but i've
tested all the values between 0 and 255 with no success !!!

An exemple of my code to write into slave's register :

// address : address of the slave
// reg : address of the slave's register
// data : value  wich write in the slave's register

void i2c_write(unsigned char address, unsigned char reg, unsigned char data)
{
 
// write address
  IOWR_I2C_TXR(address);
  IOWR_I2C_CR(OC_I2C_STA | OC_I2C_WR | OC_I2C_ACK );
  i2c_wait_tip();
  i2c_rxack();
 
  // write register address
  IOWR_I2C_TXR(reg);
  IOWR_I2C_CR(OC_I2C_STA | OC_I2C_WR | OC_I2C_ACK);
  i2c_wait_tip();
  i2c_rxack();

  // write data
  IOWR_I2C_TXR(data);
  IOWR_I2C_CR(OC_I2C_WR | OC_I2C_STO);
  i2c_wait_tip();
  i2c_rxack();
}

void i2c_rxack(void){
 while ((IORD_I2C_SR & OC_I2C_RXACK)> 0 ) {}
 }

I've initialized CTR (0x80) before write into slave's register

Can I have some help, please ?

Thank you very much

Regards
--
View this message in context:
http://www.nabble.com/I2c-and-Avalon-Bus-tp17530366p17530366.html
Sent from the OpenCores - IP Cores mailing list archive at Nabble.com.

_______________________________________________
http://www.opencores.org/mailman/listinfo/cores

_______________________________________________
http://www.opencores.org/mailman/listinfo/cores