« Return to Thread: Hollywood Plus Card, Setting: pixeldata_adjust_pal
Re: Hollywood Plus Card, Setting: pixeldata_adjust_pal
by hede
::
Rate this Message:
Hi,
no, I am not using NTSC.
Yes, I tested all the 4 values and probably you are right.
When I configure my DXR3-Card with the tool dxr3config (you know it?) and set the pixeldata_adjust_pal value to 0 or 2 the colours swap randomly. pixeldata_adjust_pal = 1 causes always wrong red and blue colours. And when I set pixeldata_adjust_pal to 3, everything seems to be fine (dxr3config writes the file /etc/modprobe.d/em8300:
install em8300 /sbin/modprobe adv717x && /sbin/modprobe --ignore-install em8300
remove em8300 /sbin/modprobe -r --ignore-remove em8300 && /sbin/modprobe -r adv717x
options adv717x pixelport_16bit=0 pixelport_other_pal=1 pixeldata_adjust_pal=3
options em8300 dicom_fix=1 dicom_control=1 dicom_other_pal=1 audio_driver=oss
But after a new system start, red and blue swaped randomly, but the file /etc/modprobe.d/em8300 is not changed.
What other files are imported???
no, I am not using NTSC.
Yes, I tested all the 4 values and probably you are right.
When I configure my DXR3-Card with the tool dxr3config (you know it?) and set the pixeldata_adjust_pal value to 0 or 2 the colours swap randomly. pixeldata_adjust_pal = 1 causes always wrong red and blue colours. And when I set pixeldata_adjust_pal to 3, everything seems to be fine (dxr3config writes the file /etc/modprobe.d/em8300:
install em8300 /sbin/modprobe adv717x && /sbin/modprobe --ignore-install em8300
remove em8300 /sbin/modprobe -r --ignore-remove em8300 && /sbin/modprobe -r adv717x
options adv717x pixelport_16bit=0 pixelport_other_pal=1 pixeldata_adjust_pal=3
options em8300 dicom_fix=1 dicom_control=1 dicom_other_pal=1 audio_driver=oss
But after a new system start, red and blue swaped randomly, but the file /etc/modprobe.d/em8300 is not changed.
What other files are imported???
Nicolas Boullis wrote:Hi,
On Sat, Feb 23, 2008 at 04:40:58AM -0800, hede wrote:
>
> I use MMS 1.1 RC3 with DXR3-Output (REALmagic Hollywood plus).
> Sometime the colour red and blue are swapped and sometimes everything looks
> fine. I tried all the settings for the "pixeldata_adjust_pal" option and I
> used the tool dxr3config.
> I think it is absolutely randomly if the colours are swapped or look fine.
> Starting a video from harddisk -> everything looks fine, stopping and
> starting the same video again without doing anything else -> the colours are
> swapped ?!?!
To my experience, randomly swapped colors happen with broken
"pixeldata_adjust_*" values (generally 0 ou 2, while 1 and 3 are either
stable good or stable swapped).
Sorry if the question sounds stupid, but you told you used all the
settings for "pixeldata_adjust_pal"; did you actually try the 4
possible values? Do you get the same random behavios with all? And are
you not using NTSC?
Cheers,
Nicolas
-------------------------------------------------------------------------
This SF.net email is sponsored by: Microsoft
Defy all challenges. Microsoft(R) Visual Studio 2008.
http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
_______________________________________________
Dxr3-devel mailing list
Dxr3-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/dxr3-devel
« Return to Thread: Hollywood Plus Card, Setting: pixeldata_adjust_pal
| Free embeddable forum powered by Nabble | Forum Help |
