|
»
« Return to Thread: NSLU2 stucked in "Assign mode"
Re: NSLU2 stucked in "Assign mode"
by Rod Whitby-2
::
Rate this Message:
Have a look at the upslug2 tool.
I seem to remember it being able to handle assign mode.
-- Rod
-----Original Message-----
From: "xenshs" <xenshs@...>
Date: Tuesday, Jun 16, 2009 11:47 pm
Subject: [nslu2-linux] NSLU2 stucked in "Assign mode"
To: nslu2-linux@...: nslu2-linux@...
Hello,
>
>a friend of mine gave me his "dead" nslu2 NAS. When I power it on, the "Ready/Status" led first shows up and then start blinking.
>
>I didn't know what to do so I "created" a cheap TTL to RS232 converter and added a serial port (http://www.nslu2-linux.org/wiki/HowTo/AddASerialPort).
>
>Now I'm able to monitor my NSLU2 from its serial port and here's the output of redboot:
>
>------------------
>+Ethernet eth0: MAC address 00:c0:02:01:01:02
>IP: 192.168.0.1/255.255.255.0, Gateway: 192.168.0.1
>Default server: 0.0.0.0, DNS server IP: 0.0.0.0
>
>RedBoot(tm) bootstrap and debug environment [ROMRAM]
>Red Hat certified release, version 1.92 - built 15:16:07, Feb 3 2004
>
>Platform: IXDP425 Development Platform (XScale)
>Copyright (C) 2000, 2001, 2002, Red Hat, Inc.
>
>RAM: 0x00000000-0x02000000, 0x000723a0-0x01ff3000 available
>FLASH: 0x50000000 - 0x50800000, 64 blocks of 0x00020000 bytes each.
>== Executing boot script in 2.000 seconds - enter ^C to abort
>RedBoot> boot;exec 0x01d00000
>have eRcOmM
>no node address
>Assign mode
>------------------
>
>The device is always stucked in assign mode I don't know what to do.
>
>I tried reflashing the firmware with official images without success, I also tried to reinstall it completely from a jtag interface but it's always stucked at this point.
>
>I already read the whole nslu2-linux.org website and tried a lots of things wo success.
>
>Hope to have more answers here :)
>
>Thanks, Romain
>
>
>
>------------------------------------
>
>Yahoo! Groups Links
>
>
>
>
I seem to remember it being able to handle assign mode.
-- Rod
-----Original Message-----
From: "xenshs" <xenshs@...>
Date: Tuesday, Jun 16, 2009 11:47 pm
Subject: [nslu2-linux] NSLU2 stucked in "Assign mode"
To: nslu2-linux@...: nslu2-linux@...
Hello,
>
>a friend of mine gave me his "dead" nslu2 NAS. When I power it on, the "Ready/Status" led first shows up and then start blinking.
>
>I didn't know what to do so I "created" a cheap TTL to RS232 converter and added a serial port (http://www.nslu2-linux.org/wiki/HowTo/AddASerialPort).
>
>Now I'm able to monitor my NSLU2 from its serial port and here's the output of redboot:
>
>------------------
>+Ethernet eth0: MAC address 00:c0:02:01:01:02
>IP: 192.168.0.1/255.255.255.0, Gateway: 192.168.0.1
>Default server: 0.0.0.0, DNS server IP: 0.0.0.0
>
>RedBoot(tm) bootstrap and debug environment [ROMRAM]
>Red Hat certified release, version 1.92 - built 15:16:07, Feb 3 2004
>
>Platform: IXDP425 Development Platform (XScale)
>Copyright (C) 2000, 2001, 2002, Red Hat, Inc.
>
>RAM: 0x00000000-0x02000000, 0x000723a0-0x01ff3000 available
>FLASH: 0x50000000 - 0x50800000, 64 blocks of 0x00020000 bytes each.
>== Executing boot script in 2.000 seconds - enter ^C to abort
>RedBoot> boot;exec 0x01d00000
>have eRcOmM
>no node address
>Assign mode
>------------------
>
>The device is always stucked in assign mode I don't know what to do.
>
>I tried reflashing the firmware with official images without success, I also tried to reinstall it completely from a jtag interface but it's always stucked at this point.
>
>I already read the whole nslu2-linux.org website and tried a lots of things wo success.
>
>Hope to have more answers here :)
>
>Thanks, Romain
>
>
>
>------------------------------------
>
>Yahoo! Groups Links
>
>
>
>
« Return to Thread: NSLU2 stucked in "Assign mode"
| Free embeddable forum powered by Nabble | Forum Help |
