Re: Optware cups segfaults on TS-119

>
> Hi,
>
> I have installed the cupsd package from optware on my Qnap TS-119.
> When I try to start cupsd, I just get a segmentation fault. The same
> for other cups related binaries like accept, cupsctl, lpadmin etc.
> I have the new Firmware version 3.0.0 Build 0430T on my TS-119.
>
> Here are the last lines of strace after starting cupsd:
>
> open("/opt/lib/libsasl2.so.2", O_RDONLY) = 3
> read(3, "\177ELF\1\1\1\0\0\0\0\0\0\0\0\0\3\0(\0\1\0\0\0\3500\0\0004\0\0\0"..., 512) = 512
> fstat64(3, {st_mode=S_IFREG|0755, st_size=86212, ...}) = 0
> mmap2(NULL, 117872, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_DENYWRITE, 3, 0) = 0x4049f000
> mprotect(0x404b4000, 28672, PROT_NONE)  = 0
> mmap2(0x404bb000, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_DENYWRITE, 3, 0x14) = 0x404bb000
> close(3)                                = 0
> mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x404bc000
> syscall_983045(0x404bc7f0, 0x400256ec, 0x404bcec8, 0x40025050, 0x40, 0x40025000, 0, 0xf0005, \
>     0x40025730, 0x1, 0, 0xbefdc55c, 0, 0xbefdc540, 0x88, 0x4000221c, 0x20000010, 0x404bc7f0, \
>     0, 0, 0xdb1c, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0) = 0
> mprotect(0x4049b000, 4096, PROT_READ)   = 0
> mprotect(0x40470000, 4096, PROT_READ)   = 0
> mprotect(0x40460000, 4096, PROT_READ)   = 0
> mprotect(0x40309000, 4096, PROT_READ)   = 0
> mprotect(0x402fb000, 4096, PROT_READ)   = 0
> mprotect(0x40249000, 4096, PROT_READ)   = 0
> munmap(0x4001f000, 17045)               = 0
> set_tid_address(0x404bc398)             = 12577
> SYS_338(0x404bc3a0, 0xc, 0x404bc7f0, 0xffffffec, 0x4001e400) = 0
> rt_sigaction(SIGRTMIN, {0x40230f74, [], SA_SIGINFO|0x4000000}, NULL, 8) = 0
> rt_sigaction(SIGRT_1, {0x40230e4c, [], SA_RESTART|SA_SIGINFO|0x4000000}, NULL, 8) = 0
> rt_sigprocmask(SIG_UNBLOCK, [RTMIN RT_1], NULL, 8) = 0
> getrlimit(RLIMIT_STACK, {rlim_cur=8192*1024, rlim_max=RLIM_INFINITY}) = 0
> --- SIGSEGV (Segmentation fault) @ 0 (0) ---
> +++ killed by SIGSEGV +++
>
> Does anybody have the same behaviour with cups?
>
> Thanks!
>  
>  
> Best regards
> Kay
>