« Return to Thread: help request
Re: help request
by Marvin Stodolsky
::
Rate this Message:
Myk
with
0403 Audio device: Intel Corporation 82801G
Primary device ID: 8086:27d8
Subsystem PCI_id 107b:0366
Softmodem codec or chipset from diagnostics: 0x10573057
your modem setup is OK.
Except after the:
$ sudo slmodemd -c USA --alsa hw:0,6
you should open a 2nd console and try detecting the modem with:
$ sudo wvdialconf /etc/wvdial.conf
if successful, add a line to /etc/wvdial.conf
Carrier Check = no
The closest equivlanet using KPPP would be to add an X3 into the Init string
ALso you should be able install your former Gutsy Gibbon linux-image package
Report back presently
MarvS
On Mon, Nov 10, 2008 at 10:53 PM, myk <footso@...> wrote:
>
> hi,
>
> attached is the ModemData.txt generated from my computer running Hardy Heron. the modem is a Motorola sm56.
>
> don't know if i read the txt correctly .
> i downloaded SLMODEMD.gcc4.2.tar.gz , unpacked it with Archive Manager , extracting to my home folder.
>
> is this all that's required before modem setup ?
>
> i set up the modem with command : 'sudo slmodemd -c USA --alsa hw:0,6'
>
> i use KPPP as a dialer , that's the only one that detects the modem.
>
> when dialing , it'll try attempt after attempt , each time resulting only in a NO CARRIER message.
>
> the modem worked under Gutsy Gibbon with SLMODEMD.gcc4.1 , i upgraded to Heron last night and i couldn't connect with 4.1 which is when i tried the scanmodem.
>
> your help is greatly appreciated . thank you
>
with
0403 Audio device: Intel Corporation 82801G
Primary device ID: 8086:27d8
Subsystem PCI_id 107b:0366
Softmodem codec or chipset from diagnostics: 0x10573057
your modem setup is OK.
Except after the:
$ sudo slmodemd -c USA --alsa hw:0,6
you should open a 2nd console and try detecting the modem with:
$ sudo wvdialconf /etc/wvdial.conf
if successful, add a line to /etc/wvdial.conf
Carrier Check = no
The closest equivlanet using KPPP would be to add an X3 into the Init string
ALso you should be able install your former Gutsy Gibbon linux-image package
Report back presently
MarvS
On Mon, Nov 10, 2008 at 10:53 PM, myk <footso@...> wrote:
>
> hi,
>
> attached is the ModemData.txt generated from my computer running Hardy Heron. the modem is a Motorola sm56.
>
> don't know if i read the txt correctly .
> i downloaded SLMODEMD.gcc4.2.tar.gz , unpacked it with Archive Manager , extracting to my home folder.
>
> is this all that's required before modem setup ?
>
> i set up the modem with command : 'sudo slmodemd -c USA --alsa hw:0,6'
>
> i use KPPP as a dialer , that's the only one that detects the modem.
>
> when dialing , it'll try attempt after attempt , each time resulting only in a NO CARRIER message.
>
> the modem worked under Gutsy Gibbon with SLMODEMD.gcc4.1 , i upgraded to Heron last night and i couldn't connect with 4.1 which is when i tried the scanmodem.
>
> your help is greatly appreciated . thank you
>
« Return to Thread: help request
| Free embeddable forum powered by Nabble | Forum Help |
