Hi,
I think the problem is with the sim.cfg u are using. I had the same issues with or1ksim and my sample programs. Try using the sim.cfg that we get from the toolchain after compiling the vmlinux. It worked fine for me. Edit that to suite your needs.
regards,
zakhir
--- On Sat, 7/3/09, faroudja.abid <fabid@...> wrote:
From: faroudja.abid <fabid@...>
Subject: Re: [openrisc] orpmon
To: openrisc@...
Received: Saturday, 7 March, 2009, 8:47 PM
Hello, i have the sam problem when i run simulation and i had this message : WARNING: config.uart: Invalid parameter:
enabled; ignoring. WARNING: config.uart: Invalid parameter: enabled; ignoring. ERROR: config.uart:invalid device number. ERROR: config.uart:invalid device number. could you tell me how do you resolve this problem thanks Ben Ayed Hatem wrote:
>
> Hello,
> I try to run orpmon , I compiled and I have orpmon-flash.or32 file
> when I run simulation by : or32-uclinux-sim orpmon-flash.or32 > log
> I have some probleme :
>
> WARNING: config.memory: Invalid parameter: nmemories; ignoring.
>
> WARNING: config.memory: Invalid parameter: device; ignoring.
>
> WARNING: config.memory: Invalid parameter: enddevice; ignoring.
>
> WARNING: config.memory: Invalid parameter: enddevice; ignoring.
>
> WARNING: config.memory: Invalid parameter: enddevice; ignoring.
>
> WARNING: config.sim: Invalid
parameter: spr_log; ignoring.
>
> WARNING: config.sim: Invalid parameter: spr_log_fn; ignoring.
>
> WARNING: config.ata: Invalid parameter: dev_type0; ignoring.
>
> WARNING: config.ata: Invalid parameter: dev_file0; ignoring.
>
> WARNING: config.ata: Invalid parameter: dev_size0; ignoring.
>
> WARNING: config.ata: Invalid parameter: dev_packet0; ignoring.
>
> WARNING: config.ata: Invalid parameter: dev_type1; ignoring.
>
> WARNING: config.ata: Invalid parameter: dev_file1; ignoring.
>
> WARNING: config.ata: Invalid parameter: dev_size1; ignoring.
>
> WARNING: config.ata: Invalid parameter: dev_packet1; ignoring.
>
> WARNING: dependstats stats must be enabled to do history analisis.
> WARNING: Unable to open RX file stream.
> Cannot open Ethernet RX file "eth0.rx"
>
> and log file :
> Reading
script file from 'sim.cfg'...
> Insn MMU 0KB: 1 ways, 64 sets, entry size 0 bytes
> Data MMU 0KB: 1 ways, 64 sets, entry size 0 bytes
> Verbose on, simdebug off, interactive prompt off
> Machine initialization...
> Clock cycle: 100ns
> Data cache present.
> Insn cache tag present.
> BPB simulation off.
> BTIC simulation off.
> Building automata... done, num uncovered: 0/213.
> Parsing operands data... done.
> loadcode: filename orpmon-flash.or32 startaddr=00000000
> virtphy_transl=00000000
> Not COFF file format
> ELF type: 0x0002
> ELF machine: 0x005c
> ELF version: 0x00000001
> ELF sec = 23
> Section: .reset, vaddr: 0xf0000000, paddr: 0xf0000000 offset: 0x00002000,
> size: 0x00000128
> ERR: 8-bit program load out of memory area: f0000000
> ERR: 8-bit program load out of memory area: f0000001
> ERR: 8-bit
program load out of memory area: f0000002
> ERR: 8-bit program load out of memory area: f0000003
> ERR: 8-bit program load out of memory area: f0000004
> ERR: 8-bit program load out of memory area: f0000005
> ERR: 8-bit program load out of memory area: f0000006
> ERR: 8-bit program load out of memory area: f0000007
> ERR: 8-bit program load out of memory area: f0000008
> ......
>
>
> How can'I resolve this probleme
>
-- View this message in context: http://www.nabble.com/orpmon-tp17177641p22385955.htmlSent from the OpenCores - RISC mailing list archive at Nabble.com. _______________________________________________ http://www.opencores.org/mailman/listinfo/openrisc
|
Stay connected to the people that matter most with a smarter inbox.
Take a look.
_______________________________________________
http://www.opencores.org/mailman/listinfo/openrisc
