|
»
debian's trouble with sheevaplug dev kit
|
View:
New views
2 Messages
—
Rating Filter:
Alert me
|
 |
debian's trouble with sheevaplug dev kit
by アズマ
::
Rate this Message:
hi !
I am in trouble in starting the i debian's nstaller according to the method of ur l "http://www.cyrius.com/debian/kirkwood/sheevaplug/install.html". Never the kernel booting had ended ! please give me this solution. the log is as below. eset __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** MARVELL BOARD: SHEEVA PLUG LE U-Boot 1.1.4 (Sep 14 2009 - 15:36:37) Marvell version: 3.4.19 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00 Soc: 88F6281 A0 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 256MB DRAM CS[1] base 0x10000000 size 256MB DRAM Total size 512MB 16bit width Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:512 MB Flash: 0 kB CPU : Marvell Feroceon (Rev 1) Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 3 0 Marvell>> mmcinit Error! cmd : 8, err : 0201 SD found. Card desciption is: Manufacturer: 0x01, OEM "PA" Product name: "S128B", revision 5.6 Serial number: 2423100053 Manufacturing date: 10/2005 CRC: 0x00, b0 = 0 Marvell>> fatload mmc 0:1 0x0800000 /uInitrd reading /uInitrd 2695505 bytes read Marvell>> fatload mmc 0:1 0x400000 /uImage reading /uImage 1811960 bytes read Marvell>> setenv bootargs console=ttyS0,115200n8 base-installer/initramfs-tools/driver-policy=most Marvell>> bootm 0x400000 0x0800000 ## Booting image at 00400000 ... Image Name: Debian kernel Created: 2009-10-25 10:29:53 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1811896 Bytes = 1.7 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 00800000 ... Image Name: debian-installer ramdisk Created: 2009-10-25 10:29:54 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 2695441 Bytes = 2.6 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ... Uncompressing Linux.................................................................................................................... done, booting the kernel. next, print messeages included variables are showed as belows. Marvell>> print baudrate=115200 loads_echo=0 serverip=10.4.50.5 rootpath=/mnt/ARM_FS/ netmask=255.255.255.0 console=a0000 e=ttyS0,115200 mtdparts=nand_mtd:0x100000@0(uboot)ro,0x0@0x100000(uImage),0x1ff00000@0x100000(rootfs)rw CASset=min MALLOC_len=1 ethprime=egiga0 bootargs_root=root=/dev/nfs rw bootargs_end=:::DB88FXX81:eth0:none image_name=uImage bootcmd=tftpboot 0x2000000 $(image_name);setenv bootargs $(console) $(bootargs_root) nfsroot=$(serverip):$(rootpath) ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvNetConfig) $(mvPhoneConfig); bootm 0x2000000; standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000; ethaddr=00:50:43:00:02:30 ethmtu=1500 mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 usb0Mode=host yuk_ethaddr=00:00:00:EE:51:81 nandEcc=1bit netretry=no rcvrip=169.254.100.100 autoload=no ethact=egiga0 loadaddr=0x2000000 mtd1Size=0x300000 filesize=0x44ad000 ipaddr=192.168.3.100 severip=192.168.3.3 mainlinelinux=yes arcNumber=2097 stdin=serial stdout=serial stderr=serial nandEnvBase=a0000 mainlineLinux=no enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no bootdelay=3 disaMvPnp=no enaAutoRecovery=yes pcieTune=no Environment size: 1416/131068 bytes Marvell>> the printenv is as belows. Marvell>> printenv baudrate=115200 loads_echo=0 serverip=10.4.50.5 rootpath=/mnt/ARM_FS/ netmask=255.255.255.0 console=a0000 e=ttyS0,115200 mtdparts=nand_mtd:0x100000@0(uboot)ro,0x0@0x100000(uImage),0x1ff00000@0x100000(rootfs)rw CASset=min MALLOC_len=1 ethprime=egiga0 bootargs_root=root=/dev/nfs rw bootargs_end=:::DB88FXX81:eth0:none image_name=uImage bootcmd=tftpboot 0x2000000 $(image_name);setenv bootargs $(console) $(bootargs_root) nfsroot=$(serverip):$(rootpath) ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvNetConfig) $(mvPhoneConfig); bootm 0x2000000; standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000; ethaddr=00:50:43:00:02:30 ethmtu=1500 mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 usb0Mode=host yuk_ethaddr=00:00:00:EE:51:81 nandEcc=1bit netretry=no rcvrip=169.254.100.100 autoload=no ethact=egiga0 loadaddr=0x2000000 mtd1Size=0x300000 filesize=0x44ad000 ipaddr=192.168.3.100 severip=192.168.3.3 mainlinelinux=yes arcNumber=2097 stdin=serial stdout=serial stderr=serial nandEnvBase=a0000 mainlineLinux=no enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no bootdelay=3 disaMvPnp=no enaAutoRecovery=yes pcieTune=no Environment size: 1416/131068 bytes Marvell>> ------------------------------------------the end -- To UNSUBSCRIBE, email to debian-arm-REQUEST@... with a subject of "unsubscribe". Trouble? Contact listmaster@... |
|
|
Re: debian's trouble with sheevaplug dev kit
by Martin Michlmayr
::
Rate this Message:
* アズマ <masha_kazuhra3n@...> [2009-10-25 23:03]:
> I am in trouble in starting the i debian's nstaller according to the > method of ur l > "http://www.cyrius.com/debian/kirkwood/sheevaplug/install.html". > Never the kernel booting had ended ! It will work after you execute the following commands: setenv mainlineLinux yes setenv arcNumber 2097 saveenv reset > next, print messeages included variables are showed as belows. > mainlinelinux=yes > arcNumber=2097 ... > mainlineLinux=no The variables are case-sensitive, and you have to change mainlineLinux to yes. -- Martin Michlmayr http://www.cyrius.com/ -- To UNSUBSCRIBE, email to debian-arm-REQUEST@... with a subject of "unsubscribe". Trouble? Contact listmaster@... |
| Free embeddable forum powered by Nabble | Forum Help |
