I am working on enabling sdio card using generic sdio code present in linux2.6.24.3 kernel..
The response from command 5 is fails.below is the debug messages from dmesg ..
mmc0: clock 400000Hz busmode 1 powermode 2 cs 1 Vdd 21 width 0 timing 0
mmc0: starting CMD0 arg 00000000 flags 000000c0
mmc0: req done (CMD0): 0: 00000000 00000000 00000000 00000000
mmc0: clock 400000Hz busmode 1 powermode 2 cs 0 Vdd 21 width 0 timing 0
mmc0: starting CMD8 arg 000001aa flags 000002f5
mmc0: req done (CMD8): 0: 0df80d0d 00000000 00000000 00000000
mmc0: starting CMD5 arg 00000000 flags 000002e1
mmc0: req done (CMD5): 0: 0df80d0d 00000000 00000000 00000000
mmc0: card claims to support voltages below the defined range. These will be ignored.
mmc0: clock 400000Hz busmode 1 powermode 2 cs 0 Vdd 20 width 0 timing 0
mmc0: starting CMD5 arg 00300000 flags 000002e1
mmc0: req done (CMD5): 0: 0df80d0d 00000000 00000000 00000000
mmc0: starting CMD5 arg 00000000 flags 000002e1
mmc0: req done (CMD5): 0: 0df80d0d 00000000 00000000 00000000
mmc0: starting CMD5 arg 00000000 flags 000002e1
mmc0: req done (CMD5): 0: 0df80d0d 00000000 00000000 00000000
mmc0: starting CMD5 arg 00000000 flags 000002e1
mmc0: req done (CMD5): 0: 0df80d0d 00000000 00000000 00000000
mmc0: starting CMD5 arg 00000000 flags 000002e1
mmc0: req done (CMD5): 0: 0df80d0d 00000000 00000000 00000000
mmc0: starting CMD5 arg 00000000 flags 000002e1
mmc0: req done (CMD5): 0: 0df80d0d 00000000 00000000 00000000
mmc0: starting CMD5 arg 00000000 flags 000002e1
mmc0: req done (CMD5): 0: 0df80d0d 00000000 00000000 00000000
mmc0: starting CMD5 arg 00000000 flags 000002e1
mmc0: req done (CMD5): 0: 0df80d0d 00000000 00000000 00000000
mmc0: starting CMD5 arg 00000000 flags 000002e1
mmc0: req done (CMD5): 0: 0df80d0d 00000000 00000000 00000000
mmc0: starting CMD5 arg 00000000 flags 000002e1
mmc0: req done (CMD5): 0: 0df80d0d 00000000 00000000 00000000
mmc0: starting CMD5 arg 00000000 flags 000002e1
mmc0: req done (CMD5): 0: 0df80d0d 00000000 00000000 00000000
mmc0: starting CMD5 arg 00000000 flags 000002e1
mmc0: req done (CMD5): 0: 0df80d0d 00000000 00000000 00000000
mmc0: starting CMD5 arg 00000000 flags 000002e1
mmc0: req done (CMD5): 0: 0df80d0d 00000000 00000000 00000000
mmc0: starting CMD5 arg 00000000 flags 000002e1
mmc0: req done (CMD5): 0: 0df80d0d 00000000 00000000 00000000
mmc0: starting CMD5 arg 00000000 flags 000002e1
mmc0: req done (CMD5): 0: 0df80d0d 00000000 00000000 00000000
mmc0: starting CMD5 arg 00000000 flags 000002e1
mmc0: req done (CMD5): 0: 0df80d0d 00000000 00000000 00000000
mmc0: starting CMD5 arg 00000000 flags 000002e1
mmc0: req done (CMD5): 0: 0df80d0d 00000000 00000000 00000000
mmc0: starting CMD5 arg 00000000 flags 000002e1
mmc0: req done (CMD5): 0: 0df80d0d 00000000 00000000 00000000
mmc0: starting CMD5 arg 00000000 flags 000002e1
mmc0: req done (CMD5): 0: 0df80d0d 00000000 00000000 00000000
mmc0: starting CMD5 arg 00000000 flags 000002e1
mmc0: req done (CMD5): 0: 0df80d0d 00000000 00000000 00000000
mmc0: starting CMD5 arg 00000000 flags 000002e1
mmc0: req done (CMD5): 0: 0df80d0d 00000000 00000000 00000000
mmc0: clock 0Hz busmode 1 powermode 0 cs 0 Vdd 0 width 0 timing 0
mmc0: error -145 whilst initialising SDIO card
can you please help me ... wat exactly to be done....
